Boxes - SmallPartsTray2

Settings for Finger Joints

angle
style		style of the fingers
surroundingspaces		space at the start and end in multiple of normal spaces
bottom_lip		height of the bottom lips sticking out (multiples of thickness) FingerHoleEdge only!
edge_width		space below holes of FingerHoleEdge (multiples of thickness)
extra_length		extra material to grind away burn marks (multiples of thickness)
finger		width of the fingers (multiples of thickness)
play		extra space to allow finger move in and out (multiples of thickness)
space		space between fingers (multiples of thickness)
width		width of finger holes (multiples of thickness)

Settings for Stackable Edges

angle		inside angle of the feet
bottom_stabilizers		height of strips to be glued to the inside of bottom edges (multiples of thickness)
height		height of the feet (multiples of thickness)
holedistance		distance from finger holes to bottom edge (multiples of thickness)
width		width of the feet (multiples of thickness)

Settings for Hinges and HingePins

grip_percentage
outset		have lid overlap at the sides (similar to OutSetEdge)
pinwidth		set to lower value to get disks surrounding the pins
style		"outset" or "flush"
axle		diameter of the pin hole (multiples of thickness)
grip_length		fixed length of the grips on he lids (multiples of thickness)
hingestrength		thickness of the arc holding the pin in place (multiples of thickness)

Settings for Cabinet Hinges

bore		diameter of the pin hole in mm
eyes_per_hinge		pieces per hinge
hinges		number of hinges per edge
style		style of hinge used
eye		radius of the eye (multiples of thickness)
play		space between eyes (multiples of thickness)
spacing		minimum space around the hinge (multiples of thickness)

Settings for Slide-on Lids

angle
hole_width		width of the "finger hole" in mm
second_pin		additional pin for better positioning
spring		position(s) of the extra locking springs in the lid
style		style of the fingers
surroundingspaces		space at the start and end in multiple of normal spaces
bottom_lip		height of the bottom lips sticking out (multiples of thickness) FingerHoleEdge only!
edge_width		space below holes of FingerHoleEdge (multiples of thickness)
extra_length		extra material to grind away burn marks (multiples of thickness)
finger		width of the fingers (multiples of thickness)
play		extra space to allow finger move in and out (multiples of thickness)
space		space between fingers (multiples of thickness)
width		width of finger holes (multiples of thickness)

Settings for Click-on Lids

angle		angle of the hooks bending outward
bottom_radius		radius at the bottom (multiples of thickness)
depth		length of the hooks (multiples of thickness)

Settings for RoundedTriangleEdge

height		height above the wall
r_hole		radius of hole
radius		radius of top corner
outset		extend the triangle along the length of the edge (multiples of thickness)

Settings for Mounting Edge

d_head		head diameter of mounting screw (in mm)
d_shaft		shaft diameter of mounting screw (in mm)
margin		minimum space left and right without holes (fraction of the edge length)
num		number of mounting holes (integer)
side		side of box (not all valid configurations make sense...)
style		edge style

Settings for HandleEdge

height		height above the wall in mm
hole_height		height of hole(s) in percentage of maximum hole height (handle height - 2 * material thickness)
hole_width		width of hole(s) in percentage of maximum hole width (width of edge - (n+1) * material thickness)
on_sides		added to side panels if checked, to front and back otherwise (only used with top_edge parameter)
radius		radius of corners in mm
outset		extend the handle along the length of the edge (multiples of thickness)

SmallPartsTray2 Settings

h		inner height in mm (unless outside selected)
sx		sections left to right in mm 🛈
sy		sections back to front in mm 🛈
hi		inner height of inner walls in mm (unless outside selected)(leave to zero for same as outer walls)
outside		treat sizes as outside measurements 🛈
back_height		additional height of the back wall - e top edge only
radius		radius for strengthening side walls with back_height
handle		add handle to the bottom (changes bottom edge in the front)

Default Settings

thickness		thickness of the material (in mm) 🛈
format		format of resulting file 🛈
tabs		width of tabs holding the parts in place (in mm)(not supported everywhere) 🛈
debug		print surrounding boxes for some structures 🛈
labels		label the parts (where available)
reference		print reference rectangle with given length (in mm)(zero to disable) 🛈
inner_corners		style for inner corners 🛈
burn		burn correction (in mm)(bigger values for tighter fit) 🛈

Assemble inside out. If there are inner front to back walls start with attaching the floor boards to them. Then add the vertical inner left to right walls. After sliding in the slopes attach the outer wall to fix everything in place.

If there are no inner front to back walls just add everything to one side wall and then add the other one after that. Possibly saving the front and back as last step.

Boxes.py

SmallPartsTray2